模糊综合评价法在钢铁企业安全投资合理性评价中的应用

为了对钢铁企业安全投资进行模糊综合评价,建立了钢铁企业安全投资的评价体系,确定各因素的权重。得出模糊综合评价矩阵,可对各因素进行评价分析;得出某钢铁企业安全投资现状分数为83.9分,等级为较好,需着重加强安全培训、劳保品、工业卫生等人因素方面的投资;在环境方面的投资较合理。     

纳米铁氧化物吸附处理重金属废水的研究进展

概述了用于吸附重金属的主要纳米铁氧化物的种类及其吸附效果,介绍了常见的纳米铁氧化物制备方法及改性方法,讨论了影响纳米铁氧化物吸附重金属的主要因素,并对纳米铁氧化物在水环境保护领域中的研究方向提出了展望:如发展绿色、高效的纳米铁氧化物制备工艺,探讨纳米铁氧化物结构调控和表面功能化对其吸附性能的影响等。     

Fe0/厌氧微生物联合体系处理2,4,6-三氯酚影响因素的研究

利用Fe⁰/厌氧微生物联合体系对2,4,6-三氯酚(2,4,6-TCP)进行降解研究。结果表明，Fe0/厌氧微生物联合体系可以有效降解2,4,6-TCP，Fe⁰与厌氧微生物之间存在明显的协同效应。Fe⁰/厌氧微生物联合体系处理2,4,6-TCP的最优条件为：微生物接种量0.434 g VSS/L，Fe⁰投加量15 g/L，体系初始pH值7.0～8.0。     

氨基改性生物炭负载纳米零价铁去除水中Cr(VI)

以聚乙烯亚胺（PEI）为功能单体,玉米秸秆生物炭为载体,制备了氨基改性生物炭负载型纳米零价铁（nZVI@PEI-HBC）,并利用扫描电镜（SEM）、红外光谱（FTIR）和X射线光电子能谱（XPS）等手段对材料进行了表征,分析了溶液pH、温度、材料投加量等因素对其去除Cr（VI）的影响及其去除机理.结果表明：在投加量为0.5 g·L^-1,温度为20℃,pH值为5,Cr（VI）初始浓度为20 mg·L^-1条件下,各材料对Cr（VI）的去除率大小为nZVI@PEI-HBC > nZVI > PEI-HBC > HBC.SEM显示nZVI颗粒较均匀地分散在生物炭表面,FTIR分析表明PEI改性后材料表面增加了氨基等重金属配位基团,这可能是nZVI@PEI-HBC去除Cr（VI）效果更好的原因.影响因素研究表明,材料具有较好稳定性,老化28 d后其Cr（VI）去除性能变化不大;酸性环境、升温、增大材料投加量均有利于nZVI@PEI-HBC对Cr（VI）的去除.机理研究发现,水中溶解氧加速了nZVI的腐蚀和Fe（II）的释放,促进Cr（VI）还原为Cr（III）,然后通过共沉淀作用和氨基等基团的吸附作用被去除.     

AMD铁絮体改性生物炭对重金属吸附机理研究 ——以Pb(II)为例

以酸性矿山废水生成的铁絮体和秸秆生物炭为原料,采用化学改性和紫外辐射联用技术制备改性生物炭,并通过正交试验确定最佳改性条件,同时利用FTIR、SEM和BET等方法对吸附材料的形貌特征、孔隙结构及其表面化学性质进行表征.结果表明,通过改性使吸附材料比表面积增大,吸附位点增多,在25℃、pH为7时,吸附材料改性后比表面积为295.71 m²·g^-1,对Pb（II）的拟合吸附量可达278 mg·g^-1.改性材料对Pb（II）的吸附过程符合Langmuir吸附等温线模型和准二级动力学模型,主要为单分子层吸附,受化学吸附控制.     

色氨酸对生物成因铁硫酸盐次生矿物形成的影响

采用氧化亚铁硫杆菌催化合成铁硫酸盐次生矿物,研究不同L-色氨酸添加浓度对矿物合成体系pH、氧化还原电位（ORP）、Fe²⁺氧化率、总Fe沉淀率,以及次生矿物产量、化学组成及矿物相的影响.结果表明,随着体系色氨酸浓度的增加,pH降低幅度越小,ORP上升越不明显.色氨酸对铁硫酸盐次生矿物合成的影响依赖于其浓度,当色氨酸浓度低于1.67 g·L^-1时,色氨酸对铁硫酸盐次生矿物的形成起促进作用,表现为总Fe沉淀率及矿物产量随着色氨酸浓度升高而增加.而当色氨酸浓度升高至6.67 g·L^-1时,Fe²⁺氧化率、总Fe沉淀率和矿物产量远低于对照组,表明高浓度色氨酸会抑制铁硫酸盐次生矿物的形成.次生矿物内Fe/S比介于施氏矿物和黄钾铁矾的理论值之间,表明不同合成体系所得次生矿物均为黄钾铁矾和施氏矿物的混合物.矿物学特征分析表明,随着色氨酸浓度的升高,矿物的合成表现为黄钾铁矾向施氏矿物转移.     

不同浓度锌处理下水稻幼苗对镉的累积效应

为探究锌（Zn）对水稻镉（Cd）累积的影响及其根表铁膜所发挥的作用,选取Cd高累积型水稻品种中9优547（简称"Z547"）和Cd低累积型水稻品种金优402（简称"J402"）,采用温室水培试验,研究0、2、5、10、15和20 μmol/L等6个Zn浓度下水稻幼苗对Cd的累积效应,以及不同浓度Zn处理对根表铁膜生成量的影响.结果表明:①随着c（Zn）的增加,Z547和J402水稻幼苗生物量均呈先增后减的趋势,分别在c（Zn）为2和10 μmol/L时达到最大值.②Z547和J402水稻幼苗中w（Cd）均呈先降后增的趋势,分别在c（Zn）为5和2 μmol/L时达到最小值;当水稻幼苗中w（Cd）达到最小值时,Z547根和地上部中w（Cd）分别为31.65和11.47 mg/kg,J402根和地上部中w（Cd）分别为22.58和14.36 mg/kg.③不同浓度Zn处理下水稻幼苗各部位中w（Cd）均与根表铁膜中w（Mn）、w（Fe）、w（Fe+Mn）呈显著正相关,高铁膜处理水稻幼苗中w（Cd）显著高于低铁膜处理,表明根表铁膜生成量的增加会促进Cd在水稻幼苗中的累积.研究显示,当c（Zn）较低时,c（Zn）的增加会抑制水稻幼苗对Cd的累积;当c（Zn）较高时,c（Zn）的增加会促进水稻幼苗对Cd的累积,而Zn可通过控制根表铁膜的生成来影响水稻幼苗对Cd的累积.      

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

邻苯二甲酸二丁酯降解过程的单体同位素分析

研究对比了邻苯二甲酸二丁酯（DBP）在不同降解过程（水解、UV/H₂O₂光解、直接光解、过硫酸钾光氧化）中的碳、氢同位素组成变化、分馏特征及二维同位素（Δδ²H-Δδ¹³C）的相关性.水解反应中DBP分子产生了显著的碳同位素分馏,未发现氢同位素分馏,而且碳同位素富集因子ε_C为（-2.7±0.4）‰,表明DBP水解时发生C-O键断裂,氢原子不参与反应.而UV/H₂O₂光解和直接光解反应（pH值分别为2、7和10）中,DBP分子呈现了相似的二维同位素相关性Λ值[（9±2）~（11±2）],推测经历了相同的反应过程.过硫酸钾光氧化降解时,明显偏大的Λ值（31±3）说明反应可能发生C-H键断裂.结果表明：二维单体同位素分析（2D-CSIA）技术可以有效区分DBP的水解、光解、光氧化3种不同类型的降解过程,有助于分析其降解路径.     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.